el133-pico-driver - GitLite

KO | EN

gitlite — search

#python #machine-learning #macos #go #swift #android #command-line #agent #chatgpt #generative-ai

el133-pico-driver

(★ 20)

Minimal standalone driver for the Pimoroni Inky Impression 13.3 (EL133UF1 / Spectra 6) on a Pico Plus 2 W: panel bring-up, test patterns, and on-device JPEG decode + dither.

파일 탐색기

ZIP 다운로드

- el133.h
- epd_io.h
- images.h
- img_decode.h
- patterns.h
- picojpeg.h
- psram.h
- - picojpeg.c
- el133.c
- epd_io.c
- img_decode.c
- main.c
- patterns.c
- psram.c
- sample.jpg
- sample_card.bin
- sample_card.S
- sample_jpg.S
- fetch_sample_jpg.py
- gen_sample.py
- make_sample_jpg.py
- png2frame.py
.gitignore
LICENSE
NOTICES.md
platformio.ini
README.md

# CDN으로 사용하기

jsDelivr

jsDelivr는 공개 GitHub 리포지토리를 별도 설정 없이 CDN으로 즉시 서빙합니다. 버전과 파일을 고르면 웹페이지에 바로 붙일 수 있는 링크와 예시 코드가 만들어집니다.

버전

파일

링크

예시

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

Minimal standalone driver for the **Pimoroni Inky Impression 13.3"**
(EL133UF1 / Spectra 6, 1600x1200, 6-colour) on a **Pimoroni Pico Plus 2 W**
(RP2350B). It brings the panel up, draws a set of test patterns and an embedded
sample image, and advances one screen per press of the front button. No WiFi,
MQTT, deep sleep, or config — just the panel.

Extracted from the `tesserae-device-pico-bin` firmware as a clean reference /
bring-up tool for this panel.

## Hardware

Pico Plus 2 W on a Hard Stuff "Pico to Pi Hat" adapter, driving the Inky 13.3".
The adapter is a 1:1 Pi-BCM-to-Pico-GP passthrough **except it swaps clock and
data** (meter-verified; the vendor doc is wrong).

| Signal | Pico GP |
| --- | --- |
| SCLK | GP10 (SPI1 SCK) |
| MOSI | GP11 (SPI1 TX) |
| DC | GP22 |
| RST | GP27 |
| BUSY | GP17 (active **low**) |
| CS_M (left half, cols 0..599) | GP26 |
| CS_S (right half, cols 600..1199) | GP16 |
| Button A | GP15 (active low) |

The panel is **landscape-native 1600x1200**, but its two controllers scan a
1200x1600 portrait frame split at column 600. The driver rotates a landscape
frame 90 deg CW and splits it; patterns are drawn directly in portrait. Spectra 6
panels need a ~300 ms per-command D/C setup or they drop commands, and a full
refresh takes ~35 s.

## Build / flash / monitor

PlatformIO core: `~/.platformio/penv/bin/pio` (adjust if yours is on PATH).

```sh
pio run                       # build -> .pio/build/pimoroni_pico_plus_2w/firmware.uf2
pio device monitor            # 115200 baud
```

Flashing (no `pio run -t upload` — the bundled picotool can't force this RP2350
into BOOTSEL): double-tap **RESET** to mount the `RP2350` drive, then copy
`firmware.uf2` onto it. (A 1200-baud touch on the USB CDC port also triggers
BOOTSEL.)

## What it does

On boot it paints the vertical-stripe test pattern, then each **button A** press
advances to the next screen:

1. vertical stripes (on boot)
2. an embedded JPEG decoded and dithered to the panel **on the device**
3. the pre-packed embedded sample image (`sample_card`)
4. horizontal stripes  5. checkerboard
6. colour blocks (3x2 of the six colours)  7. solid white

The two image screens come right after boot so they're reachable in one or two
presses — the on-device JPEG is the slow one (decode + ~35 s refresh) and was
tedious to reach when it sat last. Each paint includes the ~35 s refresh; wait for
the panel to settle before pressing A again. Serial logs each step.

## Images

There are two image paths: a frame packed on the host, and a JPEG converted on
the device itself.

### Pre-packed `.bin` (host-converted)

`src/sample_card.bin` is a landscape 1600x1200 Spectra-6 packed-4bpp frame
(960000 bytes), embedded into flash via `src/sample_card.S` (`.incbin`) and shown
directly by `el133_show_frame()` (no decode, no PSRAM).

- Regenerate the synthetic test card (no deps): `python3 tools/gen_sample.py`
- Use your own image (needs Pillow): `python3 tools/png2frame.py photo.png`
  — it cover-fits to 1600x1200, quantises to the Spectra 6 palette, and
  overwrites `src/sample_card.bin`. Rebuild and reflash.

Frame format: packed 4bpp, 2 px/byte, high nibble = even column, 800 bytes/row,
1200 rows. Colour codes: black 0x0, white 0x1, yellow 0x2, red 0x3, blue 0x5,
green 0x6.

### On-device JPEG decode + dither

`src/sample.jpg` is a 1600x1200 baseline JPEG embedded the same way
(`src/sample_jpg.S`). At paint time `img_decode_jpeg()` (`src/img_decode.c`)
decodes it with the vendored **picojpeg** into a full RGB888 buffer in PSRAM,
then Floyd-Steinberg dithers it to the six panel colours, packing the result into
a second PSRAM buffer that `el133_show_frame()` paints. This mirrors what a
networked client does with a server-delivered photo, no host conversion needed.

The dither boosts saturation ~1.4x and snaps to the *nominal* sRGB primaries
(pure red/green/blue, not muted "as it renders" targets). Muted targets — a
navy-ish blue especially — sit close to dusty-pink/mauve shadow tones, so shadows
snap to blue and the dither smears them into a violet haze; pure primaries keep
the colour decisions clean and let the panel do its own gamut projection.

- **PSRAM is required** (the RGB buffer is 5.76 MB and the packed frame 0.96 MB,
  both in the Pico Plus 2 W's 8 MB APS6404). On a board without PSRAM the screen
  is skipped with a serial note.
- The bundled sample is a royalty-free tulip photo (see `NOTICES.md`). Fetch and
  crop it reproducibly with `python3 tools/fetch_sample_jpg.py`, or point it at
  your own file: `python3 tools/fetch_sample_jpg.py --src photo.jpg`.
- For a synthetic gradient instead (needs Pillow; `numpy` optional, just faster):
  `python3 tools/make_sample_jpg.py`.
- To show your own photo directly, save it as a **1600x1200 baseline JPEG** over
  `src/sample.jpg` and rebuild — the decoder does not resize, so it clips a larger
  image and white-pads a smaller one.

## Layout

- `include/epd_io.h` / `src/epd_io.c` — SPI1 + D/C/RST/BUSY transport, command +
  data-stream helpers.
- `include/el133.h` / `src/el133.c` — the EL133UF1 driver: reset, the verified
  Pimoroni init sequence, the rotate/split paint, and refresh.
  `el133_show_pattern()` (per-row generator) and `el133_show_frame()` (landscape
  buffer).
- `include/patterns.h` / `src/patterns.c` — the procedural test patterns.
- `include/images.h` / `src/sample_card.S` / `src/sample_card.bin` — the embedded
  pre-packed image; `src/sample_jpg.S` / `src/sample.jpg` — the embedded JPEG.
- `include/img_decode.h` / `src/img_decode.c` — on-device JPEG decode +
  Floyd-Steinberg dither to a Spectra-6 frame in PSRAM.
- `include/psram.h` / `src/psram.c` — RP2350 QMI bring-up for the 8 MB PSRAM.
- `include/picojpeg.h` / `src/vendor/picojpeg.c` — vendored picojpeg (public
  domain) baseline JPEG decoder.
- `src/main.c` — boot, PSRAM init, button-A advance loop.
- `tools/gen_sample.py`, `tools/png2frame.py` — pre-packed `.bin` tooling;
  `tools/make_sample_jpg.py` (synthetic gradient) and `tools/fetch_sample_jpg.py`
  (fetch/crop a real photo) — embedded-JPEG tooling.

## License

AGPL-3.0-or-later (`LICENSE`). The vendored picojpeg decoder
(`src/vendor/picojpeg.c`) is public domain, and the bundled sample photo
(`src/sample.jpg`) is CC BY-SA 3.0; see `NOTICES.md` for both.